In-Sink-Erator - InSinkErator Evolution Compact Product Demo
InSinkErator Evolution Compact Features
View 1
- Quiet Collar® Sink Baffle:
The baffle's design causes running water to pool in the sink's opening. The resulting "water dam" acts as a cap on the disposer and reduces the noise from the sink's opening.
- Anti-Vibration Mount® Feature:
The Anti-Vibration Mount isolates the disposer in a cushion of rubber, which reduces the transfer of noise and vibration from the disposer to the sink.
- GrindShear Ring® Feature:
The ideal solution for stringy foods like cornhusks and celery is the GrindShear ring. It first grinds food into smaller particles along the surface of the ring. Then, the leftover particles are forced through a series of 40 pass-through windows and sheared into even finer waste.
InSinkErator Evolution Compact Zoom
See Flash demo for product images and multimedia.
InSinkErator Evolution Compact Specs
Specification 1
Type of Feed: Continuous
On/Off Control: Wall Switch
Motor: Single Phase
HP: 3/4
Volts: 120
HZ: 60
RPM: 1725
Amp. (Avg. Load): 8.1
Time Rating: Intermittent
Lubrication: Permanently Lubricated Upper & Lower Bearings
Shipping Weight (Approx.): 19.5 lbs.
Unit Finish: Black Enamel/Gray
Overall Height: 12-1/8"
SoundSeal Technology:
- Anti-Vibration Mount®
- Anti-Vibration Tailpipe Mount
- Quiet Collar® Sink Baffle
- SoundLimiter Insulation
MultiGrind Technology: GrindShear Ring®
Grind Chamber Capacity: 34.6 oz.
Motor Protection: Manual Reset Overload
Average Water Usage: Approx. 1 Gallon Per Person Per Day
Average Electrical Usage : 3-4 KWH Per Year
Drain Connection: 1-1/2" Anti-Vibration (Hose Clamp)
Dishwasher Drain Connection: Yes
InSinkErator Evolution Compact Video
See Flash demo for product images and multimedia.
InSinkErator Evolution Compact Install/Replace
- Tools and Materials Needed
- Slotted Screwdriver
- Adjustable Pliers
- Plumber's Putty
- Electrical Tape
- Wire Nuts (2)
- Optional Tools and Materials
- Phillips Screwdriver
- Drain Auger
- 3/8" Electrical Clamp Connector
- Second 1 1/2" Drain Trap
- Hammer
- Hacksaw
- Water Hose Clamp
- Pipe Wrench
- Copper Ground Wire
- Dishwasher Drain Connector Kit
- Air Gap
- Drain Tube Extension
- Electrical On/Off Switch or InSinkErator SinkTop Switch
- InSinkErator Power Cord Kit
- Overview
- Turn off power
- Remove existing disposer
- Check condition of mounting hardware
- Connect drain and install disposer
- Remove Existing Disposer
- Turn off power
- Disconnect drain trap
- Loosen mounting ring
- Disconnect electrical connections
- Remove Mounting Hardware
- Loosen mounting screws
- Pry off snap ring
- Remove mounting assembly
- Push old sink flange up through sink hole
- Install Mounting Bracket
- Place putty around opening
- Press flange into place
- Slide on pieces from under the sink
- Tighten bracket
- Tap Out Knockout Plug
- If needed, tap out dishwasher plug
- Lay disposer on its side
- Mounting Preparation
- Lay disposer on its side
- Make electrical connections
- Installation of Disposer
- Mount disposer under sink
- Connect discharge tube to drain plumbing
- Connect dishwasher drain to disposer
- Lock the disposal into place
- Insert Quiet Collar baffle
- Final Steps
- Lock the disposer into place
- Test for leaks
- Turn electrical on and test operation
InSinkErator Evolution Compact New Long Copy
See Flash demo for product images and multimedia.