In-Sink-Erator - InSinkErator Evolution Essential Product Demo

InSinkErator Evolution Essential Features

  • View 1

    • Quiet Collar® Sink Baffle:

      Baffle design causes running water to pool in the sink opening. The resulting thin “water dam” acts as a cap on the disposer and reduces the amount of noise that comes up through the sink opening.

    • Anti-Vibration Mount® Feature:

      The Anti-Vibration Mount isolates the disposer in a cushion of rubber, which reduces the transfer of noise and vibration from the disposer to the sink.

    • GrindShear Ring® Feature:

      Grinds food in two stages. First, food waste material is ground into small particles along the surface of the ring. Second, the particles are forced through a series of 40 pass-through windows and sheared into even finer waste. The ideal solution for stringy foods like cornhusks and celery.


InSinkErator Evolution Essential Zoom

See Flash demo for product images and multimedia.


InSinkErator Evolution Essential Specs

  • Specification 1

    • Type of Feed: Continuous
      On/Off Control: Wall Switch
      Motor: Single Phase
      HP: 3/4
      Volts: 120
      HZ: 60
      RPM: 1725
      Amp. (Avg. Load): 8.1
      Time Rating: Intermittent
      Lubrication: Permanently Lubricated Upper & Lower Bearings
      Shipping Weight (Approx.): 20.8 lbs.
      Unit Finish: Black Enamel/Gray
      Overall Height: 12-5/8"
      SoundSeal Technology:

      • Anti-Vibration Mount®
      • Anti-Vibration Tailpipe Mount™
      • Quiet Collar® Sink Baffle
      • SoundLimiter™ Insulation

      MultiGrind Technology: GrindShear Ring®
      Grind Chamber Capacity: 40 oz.
      Motor Protection: Manual Reset Overload
      Average Water Usage: Approx. 1 Gallon Per Person Per Day
      Average Electrical Usage: 3-4 KWH Per Year
      Drain Connection: 1-1/2" Anti-Vibration (Hose Clamp)
      Dishwasher Drain Connection: Yes


InSinkErator Evolution Essential Media Player

See Flash demo for product images and multimedia.


InSinkErator Evolution Essential Install/Replace

  • Tools and Materials Needed
    • Slotted Screwdriver
    • Adjustable Pliers
    • Plumber's Putty
    • Electrical Tape
    • Wire Nuts (2)
  • Optional Tools and Materials
    • Phillips Screwdriver
    • Drain Auger
    • 3/8" Electrical Clamp Connector
    • Second 1 1/2" Drain Trap
    • Hammer
    • Hacksaw
    • Water Hose Clamp
    • Pipe Wrench
    • Copper Ground Wire
    • Dishwasher Drain Connection Kit
    • Air Gap
    • Drain Tube Extension
    • Electrical On/Off Switch or InSinkErator SinkTop Switch™
    • InSinkErator Power Cord Kit
  • Overview
    • Turn off power
    • Remove existing disposer
    • Check condition of mounting hardware
    • Connect drain and install disposer
  • Remove Existing Disposer
    • Turn off power
    • Disconnect drain trap
    • Loosen mounting ring
    • Disconnect electrical connections
  • Remove Mounting Hardware
    • Loosen mounting screws
    • Pry off snap ring
    • Remove mounting assembly
    • Push old sink flange up through sink hole
  • Install Mounting Bracket
    • Place putty around opening
    • Press flange into place
    • Slide on pieces from under the sink
    • Tighten bracket
  • Tap Out Knockout Plug
    • If needed, tap out dishwasher plug
    • Lay disposer on its side
  • Mounting Preparation
    • Lay disposer on its side
    • Make electrical connections
  • Install Disposer
    • Mount disposer under sink
    • Connect discharge tube to drain plumbing
    • Connect dishwasher drain to disposer
    • Lock the disposal into place
    • Insert Quiet Collar baffle
  • Final Steps
    • Lock the disposer into place
    • Test for leaks
    • Turn electrical on and test operation


InSinkErator Evolution Essential New Long Copy

See Flash demo for product images and multimedia.


Easy2 Technologies