In-Sink-Erator - Insinkerator Evolution Excel Disposer Product Demo

Insinkerator Evolution Excel Disposer Intro

See Flash demo for product images and multimedia.


Insinkerator Evolution Excel Disposer Features

  • View 1

    • Quiet Collar™ Sink Baffle: The baffle's design causes running water to pool in the sink's opening. The resulting "water dam" acts as a cap on the disposer and reduces the noise from the sink's opening.
    • Anti-Vibration Mount™: The Anti-Vibration Mount isolates the disposer in a cushion of rubber, which reduces the transfer of noise and vibration from the disposer to the sink.
    • Multi-Layer Soundlimiter™ Insulation: The multiple layers of open and closed cell material both muffle and trap noise emitted by the disposer.
    • GrindShear™ Ring: The ideal solution for stringy foods like cornhusks and celery is the GrindShear ring. It first grinds food into small particles along the surface of the ring. Then, the leftover particles are forced through a series of 40 pass-through windows and sheared into even finer waste.
    • Tri-Action Lug System™: Swivel lugs work with the GrindShear Ring to perform the first and second stages of grind. The system’s lug configuration propels water throughout the grind chamber, helping to rinse it clean.
    • Undercutter Disk™: Located along the leading edge of the shredder plate, the undercutter mechanism performs the third stage of grind. It cuts particles one more time after they’ve passed through the GrindShear ring to help eliminate clogs.
    • Jam-Sensor Circuit™: The Jam-Sensor Circuit senses when a jam is imminent and engages, increasing rotational torque 500% while simultaneously pulsing 60 times per second. It also produces a powerful hammering effect that breaks through the toughest jams before you even notice a problem.


Insinkerator Evolution Excel Disposer Zoom

See Flash demo for product images and multimedia.


Insinkerator Evolution Excel Disposer Specs

Type of Feed: Continuous:
On/Off Control: Wall Switch:
Motor: Single Phase
HP: 1.0
Volts: 120
Reversing: Auto-Reverse Grind System™ feature
HZ: 60
RPM: 1725
Amp. (Avg. Load): 10.2
Time Rating: Intermittent
Lubrication: Permanently Lubricated Upper & Lower Bearings
Shipping Weight (Approx.): 25.5 lbs.
Unit Finish: Stainless Steel Light Gray TEN-1706
Overall Height: 13-1/2”
SoundSeal Plus Technology:
  • Anti-Vibration Mount™
  • Anti-Vibration Tailpipe Mount™
  • Quiet Collar™ Sink Baffle
  • Multi-Layer SoundLimiter™ Insulation
MultiGrind Plus Technology:
  • GrindShear Ring™
  • Tri-Action Lug System™ feature
  • Undercutter Disk™
  • Jam-Sensor Circuit™
Grind Chamber Capacity: 40 oz.
Motor Protection: Manual Reset Overload
Average Water Usage: 1/4 Gallon Per Person Per Day
Average Electrical Usage: 1/2 KWH Per Month
Drain: 1-1/2” Anti-Vibration Connection: (Hose Clamp)
Dishwasher Drain Connection: Yes


Insinkerator Evolution Excel Disposer Installation

  • Tools and Materials Needed
    • Slotted Screwdriver
    • Adjustable Pliers
    • Plumber's Putty
    • Electrical Tape
    • Wire Nuts (2)
  • Optional Tools and Materials
    • Phillips Screwdriver
    • Drain Auger
    • 3/8" Electrical Clamp Connector
    • Second 1 1/2" Drain Trap
    • Hammer
    • Hacksaw
    • Water Hose Clamp
    • Pipe Wrench
    • Copper Ground wire
    • Dishwasher Drain Connection Kit
    • Air Gap
    • Drain Tube Extension
    • Electrical On/Off Switch or InSinkErator SinkTop Switch™
    • InSinkErator Power Cord Kit
  • Overview
    • Turn off power
    • Remove existing disposer
    • Check condition of mounting hardware
    • Connect drain and install disposer
  • Removing Existing Disposer
    • Turn off power
    • Disconnect drain trap
    • Loosen mounting ring
    • Disconnect electrical connections
  • Removing Mounting Hardware
    • Loosen mounting screws
    • Pry off snap ring
    • Remove mounting assembly
    • Push old sink flange up through sink hole
  • Installing Mounting Bracket
    • Place putty around opening
    • Press flange into place
    • Slide on pieces from under the sink
    • Tighten bracket
  • Tap Out Knockout Plug
    • If needed, tap out dishwasher plug
    • Lay disposer on its side
  • Mounting Preparation
    • Lay disposer on its side
    • Make electrical connections
  • Installation of Disposer
    • Mount disposer under sink
    • Connect discharge tube to drain plumbing
    • Connect dishwasher drain to disposer
    • Lock the disposal into place
    • Insert Quiet Collar baffle
  • Cover Control Model Installation
    • Mount disposer under sink
    • Connect discharge tube to drain plumbing
    • Connect dishwasher drain to disposer
    • Lock the disposal into place
    • Snap the cover control into place
  • Final Steps
    • Lock the disposer into place
    • Test for leaks
    • Turn electrical on and test operation


Insinkerator Evolution Excel Disposer New Long Copy

See Flash demo for product images and multimedia.


Easy2 Technologies