Loading

Watts - Watts Hot Water Recirculating System Product Demo

Watts Hot Water Recirculating System Intro

See Flash demo for product images and multimedia.

 

Watts Hot Water Recirculating System Features

  • View 1

    • Easy to Install:
      • Easy to Install
      • Maintenance Free
      • Saves up to 20,000 gallons per year
      • Backed by the Watts 130 year reputation of excellence
    • Cost:
      • Costs only $0.05/day
      • 24-hour timer activates pump as needed
    • Instant Hot Water:

      This pump fills the line with hot water when it’s activated by a built-in timer.  At the furthest point of use, the bypass sensor flushes the cold water back to the heater.

 

Watts Hot Water Recirculating System Installation

  • Turn Off Water

    First, shut off the power and water supply to the water heater, according to your water heaters instruction manual.

  • Drain Water From Line

    Drain the water from the line by opening the hot water valve at the farthest faucet from the heater until the water stops flowing. Leave this valve open until you need to restart the system.

  • Drain Water Heater

    Now, drain the remaining water from the water heater drain.

  • Disconnect Water Heater

    Disconnect the connector from the hot water side of the water heater.

  • Install Pump

    Install the pump onto the water heater discharge. The pump should be installed so that it is pumping water towards the house. You can confirm the direction of water flow by checking the arrows on the body of the pump. Then, connect the pump to a flexible copper or stainless steel supply line.

  • Reopen Water Valve

    Now you can reopen the water valve to the water heater, restart your water heater according to the manufacturer’s instructions, and plug in the Watts Recirculating System pump to the nearest outlet.

  • Install Sensor Valve

    All that’s left is installing the sensor valve. For instant hot water throughout the line, it is best to install the sensor valve at the faucet located the greatest piping distance from the hot water heater. Begin by closing both the hot and cold water valves below that faucet.

  • Attach Adapters (if neccessary)

    Place the washers in the female end of the supplied adapters. Attach the adapters to both the Hot and Cold Water “out” ports.

  • Connect Flexible Lines

    Connect one end of each of the new flexible lines to the Hot and Cold Water “In” ports.

  • Disconnect Supply Lines

    Disconnect the supply lines from both valves, then reattach them to the supplied adapters.

  • Connect Line and Open Stops

    Finally, connect the other end of the new flexible line to the Hot and Cold Water valves. Now just open the stops, and your system is ready to go. If you have multiple hot water loops in your system, you will need to install additional Watts Sensor Valve Kits for each loop. “This does not require the purchase of an additional pump.”

  • Enjoy Instant Hot Water

    Now you'll never have to wait for hot water again!

 

Watts Hot Water Recirculating System Specs

  • Specification 1

      • Easy to install
      • 24 Hour Programmable Timer switch activates pump only when you need it
      • UP15-10SU7/TLC 1x115 volt
      • 3/4 inch female NPT and 3/4 inch threaded connections to mate directly to 3/4 inch hot water heater connection
      • 10 foot power cord
      • 1/2 inch Thermal Bypass Valve (sensor valve)
      • 2 -12 inch supply lines with fittings
      • No under sink pump needed
      • No under sink electrical outlet needed
      • Provides hot water instantly at every tap
      • Saves up to 20,000 gallons per year
      • Maintenance Free
      • Backed by the Watts 130 year reputation of excellence
  • Specification 2

 

Watts Hot Water Recirculating System HD Long Copy

See Flash demo for product images and multimedia.

 

Easy2 Technologies