Litex/Harbor Breeze - Harbor Breeze Calera All Weather Ceiling Fan Product Demo

Harbor Breeze Calera All Weather Ceiling Fan Intro

Harbor Breeze Calera All Weather Ceiling Fan Features

• View 1

  • 3-Speed Reversible Motor:
    • Save energy by reversing the air flow for desired air circulation in the Summer and Winter.
    • Regulate the speed of your fan - Low, Medium, or High.
  • 3 Position Mounting Options:

    3/4 in. dia. x 4 in. Downrod included.

  • Weatherproof:
    • Recommended for Wet / Damp Locations
    • Suitable for Indoor/Outdoor Applications
    • Polymer Blades
    • UL-listed for Wet Locations
  • Light Kit with Frosted Glass:
    • UL-listed for Wet Locations
    • Cap Included for use with or without Light Kit
    • Uses 2 Candelabra Base 40 Watt Max. Bulbs (not included)

Harbor Breeze Calera All Weather Ceiling Fan Finishes

Harbor Breeze Calera All Weather Ceiling Fan Installation

• Initial Installation - Step 1

  Turn off circuit breakers and wall switch to the fan supply line leads.
   
  Warning:  Failure to disconnect power supply prior to installation may result in serious injury or death.

• Initial Installation - Step 2

  Determine mounting method to use.
      A. Downrod mount (normal or angled ceiling)
      B. Closemount

  Important: If using the angle mount, check to make sure the ceiling angle is not steeper than 25°.

• Initial Installation - Step 3

  Check to make sure blades (H) are at least 30 in. from any obstruction. Check downrod (A) length to ensure blades (H) are at least 7 ft. above the floor.

• Initial Installation - Step 4

  Secure mounting bracket (C) to outlet box using screws, spring washers, and flat washers (size 8) provided with the outlet box.
  
  *Note: It is very important that you use the proper hardware when installing the mounting bracket (C) as this will support the fan. Please make certain that you purchase any hardware that is missing in order to install the mounting bracket (C) properly.

  Important: If using the angle mount, make sure open end of mounting bracket (C) is installed facing the higher point of the ceiling.
  

• Initial Installation - Step 5

  Remove motor screws (I) and lock washers (L) from underside of motor. If necessary, discard plastic.
  

• Downrod Fan Mounting - Step 1

  Insert downrod (A) through canopy (B) and weatherproof yoke cover (Y). Thread wires from motor housing (D) through downrod (A). Thread one wire through each hole in the weatherproof hanging ball cover (X). Secure weatherproof hanging ball cover (X) over hanging ball on downrod (A).

  *Helpful Hint: Downrod style mounting is best suited for ceilings 8 ft. (2.4 m) high or higher. For taller ceilings you may want to use a longer downrod (not included). Angle style mounting is best suited for angled or vaulted ceilings. A longer downrod is sometimes necessary to ensure proper blade clearance.

• Downrod Fan Mounting - Step 2

  Remove pin (R) and clip (S) from motor housing yoke. Slip downrod (A) into motor housing yoke, align holes and re-install pin (R) and clip (S). Tighten downrod (A) set screws and then tighten nuts.
  

• Downrod Fan Mounting - Step 3

  Install ball end of downrod (A) into mounting bracket (C) opening. Align slot in ball with tab in mounting bracket (C).

  Warning:  Failure to align slot in ball with tab in mounting bracket (C) may result in serious injury or death.

• Closemount Fan Mounting - Step 1

  Remove rubber washer from bottom of canopy (B).

  *Helpful Hint:  Close style mounting is more suitable for ceilings lower than 8 ft. (2.4 m) high. The downrod (A), hanging ball, and rubber washer are not used in this type of installation.

• Closemount Fan Mounting - Step 2

  Remove every other screw and lock washer from top of motor housing (D). (These screws and lock washers may already be in one of the hardware packs.)

  Remove pin (R), clip (S) and set screws from motor housing yoke.

• Closemount Fan Mounting - Step 3

  Pull wires through the canopy hole and attach canopy (B) to motor housing (D) using the three screws and three lock washers mentioned in the first paragraph of the previous step.

• Closemount Fan Mounting - Step 4

  Hang motor housing (D) on the tab on the mounting bracket (C) using one of the non-slotted holes in the canopy (B).

• Final Installation

  Temporarily lift canopy (B) to mounting bracket (C) to determine which two screws (Q) in mounting bracket (C) align with slotted holes in canopy (B) and partially loosen these two screws (Q). Remove the other two screws (Q). Now, lift canopy (B) to mounting bracket (C), aligning slotted holes in canopy (B) with loosened screws (Q) in mounting bracket (C). Twist canopy (B) to lock. Re-insert the screws (Q) that were previously removed. Tighten all screws (Q) securely.

  Complete installation instructions are included with each fan.

Harbor Breeze Calera All Weather Ceiling Fan Specs

• Specification 1

  • Fan Size
    Light Kit Adaptable
    Remote Control
    Warranty
    Mounting Method
    Number of Blades
    High Speed CFM
    Downrod Included
    Number of Lights
    Type of Bulb Needed
    Maximum Bulb Wattage
    Motor Reversible
    UL Safety Listing

  • 52"
    Light Kit Incl.
    Adaptable
    Ltd. Lifetime
    3 position
    5
    5794
    Yes
    2
    Candelabra
    40
    Yes
    Yes